Product description
ACEU-12V is power adapter with wide AC input 90~240V delivering 12V DC at 0.65Amps for a total power consumption of 7W.
AC plug is EU 220V two round pin style.
Solution is perfect for quick installation of any of the standalone versions of FRM220, FIB1 or FMC series of fiber media converters.
Same adapter can also be used for the IC series of serial converters.
This is a separate AC adapter. All our media converters: FMC, FRM220 or FIB1 series INCLUDE this AC adapter in their package.
The adapter is sold separately on this page as a back-up adapter for existing units.
Product description
The FRM220-4G-3S media converter has the ability to convert any signaling rate, from 155Mbps to 4.25Gbps, being an Universal Fiber Converter - ideal for any communication standard like: Fast and Giga Ethernet, STM-1, STM-4, STM-16, OC-1, OC-3, OC-12 and OC-48, FDDI or Fibre Channel 1/2/4G. FRM220-4G-3S has management features via SNMP or local console port (telnet) and offers active secondary optical path protection circuitry for optical redundancy. For local console the model must be purchased with a separate casing that offers serial console port, like the FRM220-CH01M or the FRM220-CH02M.
The FRM220-4G-3S is a 2R 4G optical regeneration device, which consists of Re-amplification and Re-shaping. The transponder card converts a data signal to the correct wavelength for transmission on a specific channel by supporting SFP optics on both line side and client side interfaces. 1+1 Automatic optical line Protection Switching is supported for the aggregate fiber ports. When the FRM220-4G-3S card is placed in the FRM220 rack with SNMP management, the management can view the converter card's status, type, version, fiber link status and alarms. The card can be configured to enable or disable the port, reset the port and perform diagnostic loop backs.
FRM220-4G-3S converter cand be used as card into the larger 20 slot FRM220-CH20or 8 slot FRM220-CH08chassis.
Features
Product description
The FIB1-T1R-SC20BF is a fiber media converter for G.703 T1 transmission/transport and features an RJ-48c connector for connection to 100 Ohm twisted pair wiring. FIB1-T1R-SC20BF operates on single-mode single strand fiber up to 20Km (14mi) distance. The B type model must always match a complementary A type single strand converter. Versions of 40Km, 60Km or 80Km single strand converters are available on request. B type WDM single strand converter uses Tx: 1550nm and Rx: 1310nm wavelengths.
The fiber media converter is equipped with a single SC type optical connector. The media converter is also sometimes called T1 fiber modem. When the FIB1-T1R card is placed in the FRM301 rack with SNMP management, the card status, type, version, fiber link status, E1 or T1 link status and alarms can all be displayed. Configuration is also available to enable or disable the port, reset the port, do far end fault setting, and initiate local or far end loop-back tests.
The uniqueness of FIB1-T1R is given by the ability to convert from standalone media converter to card for FRM301 chassis, in matter of minutes. In an always changing and growing networking environment, such a versatile feature allows network operators to switch to higher density and aggregation hubs without the need to purchase new fiber optic converters. This simple, but so reliable idea, made the FIB1-T1 media converter the perfect choice for media converters by data carriers and service providers.
Product description
The FRM220-DS3-E3 is an extremely versatile E3 and DS3 over fiber media converter. Any 155Mbps rate optical SFP transceiver can be installed into the single SFP slot of the media converter, offering maximum flexibility for the optical interface. FRM220-DS3-E3 can support operation on E3 75Ohms or DS3 75Ohms dual BNC coaxial copper interface. The FRM220-DS3-E3 can extend transparently over fiber any E3/DS3 signal. Unit supports local console, and future releases will include web-based and in-band mFiber Connectivity Management. The web and In-band features will be available when unit is inserted into the FRM220 in-band managed fiber chassis. FRM220-DS3-E3 can accommodate any type of miniGBIC (SFP) 155Mbps rate optical modules, either multi-mode, singlemode or single strand Bi-Directional type.
The FRM220-DS3-E3 E3 or DS3 fiber extender is extremely versatile, being available in several versions of power supply: embedded internal AC power, embedded internal DC neg. 48V power or dual combo embedded AC and DC power supply. Same model can also be installed in the FRM220chassis, in matter of minutes.
Technical specifications
| Interfaces: | dual 75Ohms BNC copper for E3/DS3 interface and SFP slot for 155Mbps fiber rate communication |
| Connectors: | dual BNC copper and SFP slot 155Mbps |
| Standards: | ANSI, ITU-TS, ETSI, AT&T, G.703, G.921 & G.955 |
| Optical slot: | Small Form Pluggable - supports Auto and Forced mode operation |
| Front LEDs: | PWR, Coax link, coax loop-back, AIS on coax link, FX link, fiber loop-back, AIS on FX link |
| Power: | Embedded 90-260V AC switching power supply with IEC C14 connector and US type main plug power cord |
| Temperature: | 0-60°C (Operating); 0-70°C (Storage) |
| Humidity: | 20 80% non condensing (Operating); 0 90% (Storage) |
| Consumption: | less than 5W |
| Dimensions(WxDxH): | 88mm x 155mm x 23mm |
| Weight: | 950g (without power cord) |
| Compliance: | CE, FCC Class A, LVD, RoHS |
| MTBF: | 65,000 hours |
3M 261X Aluminum Oxide lapping film, 9" X 13" sheet, grit 3µm.
Pack of 100 sheets.
This hand polish puck is made by CNC machines for repeated quality and accuracy. The unique design prevents vapor locking and surface tension so your connectors are polished properly.
This puck can work with LC/APC connectors.
Specifications:
Note:
This doesn't work with PC connectors. Please check
LC male-to-female attenuators contain doped fiber suitable for both 1310nm and 1550nm operation. Fixed attenuation values are available in 1dB increments from 1 to 20dB.
All Fiber Optics For Sale Co. attenuators are built with the highest quality materials and factory tested to ensure precise attenuation and performance.
ST male-to-female attenuators contain doped fiber suitable for both 1310nm and 1550nm operation. Fixed attenuation values are available in 1dB increments from 1 to 20dB.
All Fiber Optics For Sale Co. attenuators are built with the highest quality materials and factory tested to ensure precise attenuation and performance.
Aluminum Oxide polishing film.
The Air Gap Variable Attenuator has a ceramic alignment sleeve that provides a low insertion loss of .15dB and can be used on both multimode and singlemode applications. Attenuation range is 0dB to 20dB.
The attenuator comes with an included tool that provides ability to increase attenuation level to desired level
Device may replace mating sleeve at the patchpanel, enabling variable attenuation levels to be introduced to the system.
The type of variable attenuator can be installed at the distribution panels or connecting two patchcords to become in-line attenuator application. By fine tuning the air gap width, the user can easily adjust the attenuation value when using in conjunction with power meter.
LC male-to-female attenuators contain doped fiber suitable for both 1310nm and 1550nm operation. Fixed attenuation values are available in 1dB increments from 1 to 20dB.
All Fiber Optics For Sale Co. attenuators are built with the highest quality materials and factory tested to ensure precise attenuation and performance.
The capacity ofSFM-7000-L31optical module is1.25Gbps(Gigabit rate). The XR transceiver (eXtended Range) allows operation on either50/125um or 62.5/125um multi-modefiber for up to2Kmdistance. The fiber standard for SFM-7000-L31 is1000Base-SX.
All the managedFIB1-1000ESandFIB1-1000TSas well as unmanagedFMC-1000ESandFIB1-1000DSseries of standalone Gigabit media converters can be equipped with miniGBIC/SFP optical modules.
SFP's or miniGBIC modules are extremely versatile, working with any active equipment that support the SFP type of interface: Ethernet switches, routers and any other networking equipment. Our SFPs have been tested and found 100% compatible with various Ethernet switches from major manufacturers like: Cisco, Nortel, Extreme, ZyXEL, D-Link or Netgear.
1x4 Single Mode PLC Splitter (Planar Lightwave Circuit Splitter) with Fan Out & SC/APC Connectors
PLC stands for Planar Lightwave Circuit. PLC splitters are used to distribute or combine optical signals. It is based on planar lightwave circuit technology and provides a low cost light distribution solution with small form factor and high reliability.
PLC Splitters provide a cost effective and space saving product suitable to the ever changing networking requirements. With it's compact size, these splitters can be utilized in in-ground and aerial pedestals as well as rack mount systems.
Installation is simple using a variety of connector types or fusion splicing.
Applications:
Product Features:
Product Specs:
| Configuration | Insertion Loss (dB) | Uniformity (dB) |
| 1x4 | 7.0 | 0.8 |
| 1x8 | 11.5 | 1.0 |
| 1x16 | 14.5 | 1.5 |
| 1x32 | 17.5 | 2.0 |
Product description
The capacity ofSFS-7010-L31module is1.25Gbps(Gigabit rate). The transceiver is able to work on9/125um single-modefiber for up to10Kmdistance. The fiber standard for SFS-7010-L31 is1000Base-LX.
All the managedFIB1-1000ESandFIB1-1000TSas well as unmanagedFMC-1000ESandFIB1-1000DSseries of standalone Gigabit media converters can be equipped with miniGBIC/SFP optical modules.
SFP's or miniGBIC modules are extremely versatile, working with any active equipment that support the SFP type of interface: Ethernet switches, routers and any other networking equipment. Our SFPs have been tested and found 100% compatible with various Ethernet switches from major manufacturers like: Cisco, Nortel, Extreme, ZyXEL, D-Link or Netgear.
Fiber power budget according to available models
(highlighted model is one available for purchase on this page)
| Model | Distance | Lambda | Min. Output (dBm) | Sensitivity (dBm) | Power Budget (dB) |
| SFM-7000-S85 | 550m | 850nm | -9.5 | -18 | 8.5 |
| SFM-7000-L31 | 2Km | 1310nm | -9 | -19 | 10 |
| SFS-7010-L31 | 10Km | 1310nm | -9.5 | -20 | 10.5 |
| SFS-7040-L31 | 40Km | 1310nm | -4 | -24 | 20 |
| SFS-7050-X55 | 50Km | 1550nm | -4 | -24 | 20 |
| SFS-7080-Z55 | 80Km | 1550nm | 0 | -24 | 24 |
| SFS-7120-Z55 | 120Km | 1550nm | 0 | -30 | 30 |
| SFS-7010-WA | 10Km | Tx:1310nm Rx:1550nm | -9 | -21 | 12 |
| SFS-7010-WB | 10Km | Tx:1550nm Rx:1310nm | -9 | -21 | 12 |
| SFS-7020-WA | 20Km | Tx:1310nm Rx:1550nm | -8 | -23 | 15 |
| SFS-7020-WB | 20Km | Tx:1550nm Rx:1310nm | -8 | -23 | 15 |
| SFS-7040-WA | 40Km | Tx:1310nm Rx:1550nm | -3 | -23 | 20 |
| SFS-7040-WB | 40Km | Tx:1550nm Rx:1310nm | -3 | -23 | 20 |
| SFS-7060-WA | 60Km | Tx:1310nm Rx:1550nm | 0 | -24 | 24 |
| SFS-7060-WB | 60Km | Tx:1550nm Rx:1310nm | -2 | -25 | 23 |
The Clip-On Variable Fiber Optic Attenuator is a completely passive device, which works by physical attenuation of a 3mm jacketed singlemode cable.
It may also be used with smaller jacket sizes. However, attenuation performance may vary.
The clip-on attenuator can be attached at any point in a fiber cable, providing attenuation levels from 0 to >47dB at 1550nm, 0 to >21dB at 1310nm, and low back reflection.
This attenuator is good for hundreds of uses, and leaves no lasting effects on the cable.
Dimensions: Length = 1 1/2", Diameter = 3/4"
1x32 Single Mode PLC Splitter (Planar Lightwave Circuit Splitter) with Fan Out & SC/APC Connectors
PLC stands for Planar Lightwave Circuit. PLC splitters are used to distribute or combine optical signals. It is based on planar lightwave circuit technology and provides a low cost light distribution solution with small form factor and high reliability.
PLC Splitters provide a cost effective and space saving product suitable to the ever changing networking requirements. With it's compact size, these splitters can be utilized in in-ground and aerial pedestals as well as rack mount systems.
Installation is simple using a variety of connector types or fusion splicing.
Applications:
Product Features:
Product Specs:
| Configuration | Insertion Loss (dB) | Uniformity (dB) |
| 1x4 | 7.0 | 0.8 |
| 1x8 | 11.5 | 1.0 |
| 1x16 | 14.5 | 1.5 |
| 1x32 | 17.5 | 2.0 |
This Variable Attenuator uses collimator lens technology enabling the user to change attenuation through the twist of a top-mounted screw.
Use this variable attenuator to simulate the loss in a fiber system or testing your system's dynamic range. A power meter and light source can be used to determine the fixed attenuation value your system requires.
The attenuator has a 0.6 dB typical insertion loss and is available in a 2 meter length and may be connectorized.
Loctite 7649 Primer N ( Ground Shipment Only)
This item comes in a 1.75 fluid oz bottle.
LOCTITE ACTIVATOR 7649 Primer N is a single component non-CFC solvent based surface activator. The activator is designed to promote the speed of cure of Loctite anaerobic adhesives and sealants such as Loctite 680.
7649 can be used with Loctite 680 (PN:680) on specially designed Anaerobic connectors to increase the cure speed. Please refer to our connector department to get more information about these connectors.Direction for use:
Note: The OLPS-4RM-DD chassis includes two OLPS-4RM-DC48 power supplies with DC 36-72V input. OLPS-35 protection cards are NOT included with the OLPS-4RM-DD chassis.
Product description
The OLPS-4RM-DD is a high performance high density Optical Line Protection System for critical fiber optic transmission circuits. The chassis can hold up to 8 independent OLPS-35 1:1 optical protection cards. The chassis occupies 4RU of rack space offering double the density of the standalone OLPS-RM-35-AD system while bringing the cost per OLPS 1:1 protection system at the best value. The management system available on the 8 slot chassis allows management of all the OLPS-35 cards with a single IP address. The 1:1 protection system has the advantage of a very low insertion loss compared with 1+1 protection systems. The OLPS-35 cards offers only 1.2dB of insertion loss, making them a favored protection choice for tight optical budget applications.
The OLPS is an automatic system that switches fiber communication from a main fiber line to an alternate backup fiber when the main line communication is disabled. This is done by constantly monitoring the optical level of the main line. When signal level gets under a set threshold, communication is diverted on the secondary path in less than 35 miliseconds. Unit has management available via console and SNMP. Management allows set-up of threshold optical level for switching and behavior for recovery: automatic reverting to main when signal is restored, manual revert or no switch. The new OLPS-4RM chassis offers 19" rack mounting brackets with only 4RU of space used, saving vital rack space when necessary. The 8 slot OLPS rack can be loaded with OLPS-35 1:1 protection cards.
The OLPS chassis provides redundant power supply system with "hot swap" feature, to provide continuous operation. It can accomodate both AC (110V) and DC (48V) power supply units, either in mixed or same type of power input.
Technical specifications
| Chassis: | 4RU height, 19" wide mounting system |
| Optical Protection System: | 8 slots for OLPS-35 1:1 protection cards |
| Operating wavelengths: | 1310nm (+/-50nm) and 1550nm (+/-50nm) (on OLPS-35) |
| Monitored power range: | -50~+23dBm |
| Accuracy level: | +/-0.25dB |
| Insertion Loss: | Tx<1.2dB, Rx<1.2dB |
| Switching time: | <35ms |
| PDL: | <0.05dB |
| WDL: | <0.1dB |
| Dimensions(WxDxH): | 440mm x 140mm x 356mm |
| Temperature: | -10~60°C (Operating); -20~75°C (Storage) |
| Power: | dual -36 to -72V DC hot swappable power supply units, 2 slots available on chassis (optional AC 90-240V PS available on request) |
| MTBF: | 60,000 hours |
Note: Picture shows a fully loaded chassis. Only the chassis is sold under this part number.
Product description
The new SML-4000-CH high density chassis occupies 4RU space in a 19" rack and holds up to 24 different/independent CWDM or DWDM mux/demux cards from the SML-40 series. Each mux/demux card can be used as standalone or can be installed in one of the SML-4000 chassis 24 slots.
The SML-4000-CH is a rack 19" solution for very high density of CWDM or DWDM filters in a telecom rack. The solution is offering unparalleled density of CWDM or DWDM filters per unit of rack space. All CWDM or DWDM filters can be customized upon customer needs according to number of channels, specific wavelengths, expansion and monitor ports and type of connectors.
Note: Only the chassis is sold under this part number.
Product description
The new SML-1000-CH chassis occupies only 1U space in a 19" rack and holds up to 4 different/independent CWDM mux/demux cards from the SML-1000 series. Each mux/demux card can be used as standalone or can be installed in one of the SML-1000 chassis 4 slots.
The SML-1000-CH is a rack 19" solution for higher density of CWDM or DWDM filters in a telecom rack. CWDM or DWDM filters can be customized upon customer needs.
99% reagent grade isopropyl is used in cleaning fiber or connector end faces for better transmission performance.
This is a bottle of 28oz. isopropyl alchol. Alcohol must be shipped by ground only and in regulated quantities.
This is the industry's most popular, high-quality fusion splice protection sleeve.
It has a steel strength member, inner fiber tube, and outer shrink tube. After heat shrinking the size is 3.0mm diameter x 60mm length.
It is designed for single fiber applications and accommodates up to 1.4mm coated fibers. The color is clear (transparent).
Fusion splice protection sleeves provide vital protection at the fused juncture between two fusion spliced optical fibers. In addition to providing a substitute for the original fiber optic cable jacket, splice protection sleeves provide a degree of rigidity that prevents the spliced area from bending or flexing.
Features:
PA-901053 Paladin Tools CAT5 Installation DataReady Kit
The Paladin Tools 901053 DataReady tool kit includes everything needed to install CAT 5 cables -- all in a convenient zippered case. This Category 5 datacom tool set includes all-in-one crimper, punch down tool, data cable cutter, continuity tester, and 20 RJ45 connectors.
If you're installing CAT 5 cables, get the job done right with the Paladin Tools DataReady tool kit.
The Greenlee Paladin Tools PA-901053 DataReady Tool Kit is a complete solution for CAT 5e terminating. Crimper allows you to crimp, cut and strip RJ45, RJ11/RJ12 and RJ22 handset plugs, plus cut and strip 28- to 22- AWG round UTP/STP phone, data, and flat satin cable.
Paladin Kit also includes the SurePunch punchdown tool with 66/110 blade, Data SureStrip cutter/stripper, 20 RJ45 connectors, the LAN ID continuity tester and Cable Check network identifier. Complete kit organized in a soft zipper case.
Use the Paladin Tools 901053 premium DataReady Tool Kit for CAT 5e telecom terminating jobs. The 1556 WE/SS Low-Cost All-in-One Data and Telephone Tool has crimping cavities for RJ45, RJ11/RJ12 and RJ22 handset modular plugs. Use it to cut and strip 28- to 22-AWG round UTP/STP phone and data cable plus flat satin phone cable. The SurePunch PDT reduces time and effort. Soft, rubber-embedded handle with cushioned heel decreases hand strain. Includes 66/110 reversible blade.
Features:
Hitachi CAT5e UTP (Unshieled Twisted Pair) Bulk Copper Cable. Riser Rated (CMR). 1000 Feet/Box. Brown Color Jacket.
CAT5e UTP & Cat 5E+ UTP FEATURES:
One pair of brand new fusion splicer electrodes for Fujikura FSM-17S,18S,50R,50S,60S,60R Fusion Splicer models.
Equivalent Model No: S013532
